Hongqi E-HS9 Manual Download Page 230

Page: 230 / 395

5-2. Operating the multimedia system

228

Charging setting

Users can know the current charging information of the vehicle through the charging setting
interface.

State of Charge

◼

The charging port cover can be opened/closed.

Charging time

◼

You can turn on/off the scheduled charging, and set the start and stop time of the
scheduled charging.

Limit value

◼

You can set the charge/discharge limit.

Energy consumption

◼

The energy consumption value is displayed in a curve.

Setting

◼

Low battery reminder: The range of low battery reminder can be set according to the
demand.

Summary of Contents for E-HS9












































































































































































































































































































































































































Search results

Summary of Contents for E-HS9

Reviews:

Related manuals for E-HS9

Brands by name

Popular brands

Hongqi E-HS9, Manual

Search results

Summary of Contents for E-HS9

Reviews:

Related manuals for E-HS9

Brands by name

Popular brands