Hongqi E-HS9 Manual Download Page 45 | Manualshive

Page: 45 / 395

background image

1-1.Instructions for safety operation

Installing a child restraint system

43

Inst alling a c hild res traint sy stem

Please  follow  the  instructions  provided  by  the  manufacturer  of  the  child  restraint
system.  Securely  fix  the  child  restraint  system  to  the  seat  with  the  ISOFIX  rigid
anchorage.  During  the  installation  of  the  child  restraint  system  equipped  with  top
strap, the top strap shall be fixed.

Installation with ISOFIX rigid anchor

Slightly increase the gap between
the seat cushion and the
backrest.

Fit the child seat buckle to the
ISOFIX rigid anchorage and lock
securely.

If the headrest interferes with the child
restraint system and cannot be installed
correctly, rise the headrest and install the
child restraint system.

If a child restraint system is equipped with
a top strap, the top strap shall be secured
to the anchor support.

Child restraint system with top strap

Fix the child restraint system with the ISOFIX
rigid anchorage.

If  the  headrest  interferes  with  the  child
restraint  system  and  cannot  be  installed
correctly, rise  the headrest and install the
child restraint system.

STEP

«
...
43
44
45
46
47
...
»

Summary of Contents for E-HS9












































































































































































































































































































































































































Reviews:

No comments

Related manuals for E-HS9

Brand: Jeep Pages: 5

Brand: Jeep Pages: 6

Grand Cherokee SRT 2014

Brand: Jeep Pages: 345

Grand Cherokee 2015

Brand: Jeep Pages: 236

Brand: Jeep Pages: 18

Brand: Jeep Pages: 24

Brand: Jeep Pages: 560

Brand: Jeep Pages: 525

Brand: Jeep Pages: 308

Brand: Jeep Pages: 86

Brand: Jeep Pages: 638

Brand: Jeep Pages: 9

Brand: Jeep Pages: 51

Brand: Jeep Pages: 4

Brand: Jeep Pages: 50

Grand Cherokee SRT 2014

Brand: Jeep Pages: 118

2014 Grand Cherokee

Brand: Jeep Pages: 24

Brand: Jeep Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands