Hongqi E-HS9 Manual Download Page 189 | Manualshive

Page: 189 / 395

background image

4-5. Operating other driving systems

Autonomous Emergency Braking (AEB)

187

Autonom ous Emergency Br aking (AEB)

The working range of autonomous emergency braking (AEB) is 8km/h - 80km/h.
When the vehicle encounters an emergency and may collide with the vehicle ahead, if
the driver does not apply emergency braking or steering in time, the system will
assist the driver to apply braking force to the vehicle to avoid or reduce the injury of
collision.

If the AEB is activated, the alarm
information will appear on the instrument
cluster and an alarm sound will be issued.

◼

AEB on/off

You can set the on and off of AEB system in the vehicle settings of the multimedia system.
(Refer to P.225)

If the system is turned off, the instrument
cluster will show the AEB OFF indicator.

◼

Adjusting or calibrating the AEB system

Please  adjust  or  calibrate  the  AEB  system  in  the  following  cases,  otherwise  the  AEB
system may not work properly.
•  The front windshield is damaged or replaced.
•  The advanced DAS camera unit or forward millimeter wave radar positioning bracket

is removed or installed.

• The vehicle is adjusted after four wheel alignment.
• The front bumper is hit or deformed.

Please contact an authorized FAW Hongqi dealer.

«
...
187
188
189
190
191
...
»

Summary of Contents for E-HS9












































































































































































































































































































































































































Reviews:

No comments

Related manuals for E-HS9

Brand: Camoplast Pages: 60

Brand: Volvo Pages: 10

Brand: Metra Electronics Pages: 8

51 47 0 027 792

Brand: BMW Pages: 7

Brand: Ford Pages: 728

Brand: Westin Pages: 5

THERAPEDIC 2000

Brand: Columbia Pages: 14

Brand: Ford Pages: 52

Grand Cherokee SRT 2019

Brand: Jeep Pages: 656

Brand: Toyota Pages: 295

Brand: IOGear Pages: 38

OUTLANDER PHEV 2022

Brand: Mitsubishi MOTORS Pages: 8

Brand: Subaru Pages: 786

Brand: TATA Motors Pages: 146

Brand: AA Products Pages: 8

Brand: Maxon Pages: 10

Brand: Webasto Pages: 28

PLATINUM HT051202

Brand: Haltech Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands