manualshive.com logo in svg

Honeywell VISTA-128BPEN, Installation And Setup Manual

Share
Download
Honeywell VISTA-128BPEN Installation And Setup Manual Download Page 61

 

4-3 

MAIN MENU 

OPTIONS

 

 

 

ZONE PROG? 

  1 = YES  0 = NO 

0 

For programming the following: 

•

 Zone 

Number 

•

 

Zone Response Type 

•

 

Partition Number for Zone 

•

 

Dialer report code for zone 

 

•

 

Input Device Type for zone (whether RF, polling 
loop, etc.) 

•

 

Enrolling serial numbers of 5800 Series transmitters 
& serial polling loop devices into the system. 

•

 

Zone Attributes (e.g., Arm w/Fault, Silent, etc.). 

 

EXPERT MODE? 

1 = YES  0 = NO 

0 

Same as Zone Programming except: 

•

 

Done with a minimum number of keystrokes.  

•

 

Can program wireless keys using pre-defined templates. 

 

REPORT CODE PROG? 

1 = YES  0 = NO 

0 

For programming the following: 

•

 

Alarm report codes for zones 

•

 

Restore and supervisory codes 

•

 

All other system report codes 

 

ALPHA PROG? 

1 = YES  0 = NO 

0 

For entering alpha descriptors for the following: 

•

 Zone 

Descriptors 

•

 Installer’s Message 

•

 Custom 

Words 

 

•

 Partition 

Descriptors 

•

 Relay 

Descriptors 

 

DEVICE PROG? 

1 = YES  0 = NO 

0 

For defining the following device characteristics for addressable devices, including keypads, RF receivers 
(5881), output relay modules (4204/4204CF), FSA (FSA-8/FSA-24), 4286 VIP Module, Panel Link Module 
(VA8201), ECP communicator (7845GSM, 7845i-GSM), and VISTA Gateway Module: 

•

 Device 

Address 

•

 Device 

Type 

•

 

Keypad Options  (including Partition assignment) 

•

 RF 

House 

ID 

•

 

LRR Options (including Programming radio) 

 

OUTPUT PGM? 

1 = YES  0 = NO 

0 

For defining output device functions. 

 

RLY VOICE DESCR? 

1 = YES  0 = NO 

0 

For entering voice descriptors for relays to be used with the 4286 VIP Module. 

 

CUSTOM INDEX ? 

1 = YES  0 = NO 

0 

For creating custom word substitutes for VIP Module annunciation. 

 

ACCESS POINT PGM 

1 = YES  0 = NO 

0 

For defining the parameters for each of the VistaKey zones, including which group(s) have access through 
an access point (door). See the 

VistaKey-SK Installation and Setup Guide for detailed programming 

instructions. 

 

ACCESS GRP PGM 

1 = YES  0 = NO 

0 

For defining the capabilities (privileges) for each group of users. See the 

VistaKey-SK Installation and Setup 

Guide for detailed programming instructions. 

 

EVENT/ACTION PGM 

1 = YES  0 = NO 

0 

For defining events and time windows for an access group. See the 

VistaKey-SK Installation and Setup 

Guide for detailed programming instructions. 

 

SCHEDULED CHK-IN 

1 = YES  0 = NO 

0 

For defining the schedule for the system to automatically call the downloader. 

 

Summary of Contents for VISTA-128BPEN

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands