Honeywell VISTA-128BPEN Installation And Setup Manual Download Page 30

Page: 30 / 128

Vista-128BPEN Installation and Setup Guide

3-10

•

The alarm current provided by zone 8 supports only one glassbreak detector in the alarmed state.

•

Do not use other contacts when using glassbreak detectors on zone 8. Other contacts may prevent proper

glassbreak detector operation.

To wire 2-wire latching glassbreak detectors to zone 8, perform the following steps:

Step Action

Select 2-wire glassbreak detectors that meet the requirements stated previously.

Connect detectors across zone 8 (terminals 21 and 22). See

Figure 3-12

Connect the EOL resistor at the last detector in the loop across the zone’s terminals.

You must connect the

EOL resistor across the loop wires at the last detector

Tamper Supervision for the Hardwired Zones

The system can be programmed to monitor for either an open condition or a short condition of a tamper switch on zones
1-8. End-of-line supervision is required for this option.

Wiring a Tamper Switch to Zones 1-8

The wiring of the tamper switch depends on whether the tamper switch and the sensor are normally open or normally
closed.

•

If you are using a normally closed sensor,

the tamper switch must be normally open. Refer to

Figure 3-13

for

the wiring configuration.

•

If you are using a normally open sensor,

the tamper switch must be normally closed. Refer to

Figure 3-13

for

the wiring configuration.

•

For the normally closed sensor

, program the zone for trouble on short.

For the normally open sensor

program the zone for trouble on open.

To wire a tamper switch on a hardwired zone, connect the EOL resistor at the last detector in the loop across the zone’s
terminals.

You must connect the EOL resistor at the last detector for proper operation of the tamper

supervision.

NOTE:

These zones cannot be programmed for any 24 hour zone type and that tamper supervision is only in the

disarmed state. When armed goes into alarm.

NOTE:

For zones with a response type of 9 or 16 (Fire), the tamper selection must be “0” none.

2k EOLR

TAMPER
SWITCH

SENSOR

Figure 3-13: Wiring a Normally Closed Loop for Tamper Supervision

2k EOLR

TAMPER
SWITCH

SENSOR

Figure 3-14: Wiring a Normally Open Loop for Tamper Supervision

Summary of Contents for VISTA-128BPEN

































































































































Search results

Summary of Contents for VISTA-128BPEN

Reviews:

Brands by name

Popular brands

Honeywell VISTA-128BPEN, Installation And Setup Manual

Search results

Summary of Contents for VISTA-128BPEN

Reviews:

Brands by name

Popular brands