Honeywell VISTA-128BPEN Installation And Setup Manual Download Page 22 | Manualshive

Page: 22 / 128

background image

Vista-128BPEN Installation and Setup Guide

3-2

•

All unused knockouts must be plugged using the disc plugs and carriage bolts (supplied), as indicated in the
diagram below.

•

Fasten the cabinet door to the cabinet backbox using the 18 one-inch-long Phillips-head screws (supplied) after all
wiring, programming, and checkout procedures have been completed.

PC

BOARD

(Shows typical local Grade A listing installation)

RUN BELL WIRES

IN CONDUIT

PLUG THIS
KNOCKOUT

PLUG THIS

KNOCKOUT

PLUG THIS

KNOCKOUT

PLUG THIS

KNOCKOUT

RUN ALL REMAINING

WIRE THROUGH HERE

CLIP-ON DOOR
TAMPER SWITCH

CABINET
MOUNTING
HOLE
(4 PLACES)

TO PLUG AN UNUSED KNOCKOUT OPENING,

REMOVE KNOCKOUT AND INSTALL A PAIR OF

DISC PLUGS AND A CARRIAGE BOLT AS SHOWN.

KNOCKOUT

OPENING

HEX NUT AND

WASHER

DISC PLUGS (DIMPLES IN DISC
PLUG SHOULD REGISTER INSIDE
KNOCKOUT OPENING)

CARRIAGE BOLT

CABINET SIDE WALL
(OUTSIDE)

cabattack-001-V0

Figure 3-2: Cabinet Attack Resistance Considerations

•

Mercantile Safe and Vault Listing Guidelines

Follow the guidelines given above for Mercantile Premises listing.

•

Mount a shock sensor such as Sentrol No. 5402 to the control's backbox. Follow the manufacturer's instructions for
proper sensor mounting. This sensor also must be wired to a hardwire zone.

•

For safe and vault applications, a UL Listed contact must be used inside the cabinet through one of the knockouts
for pry-off tamper purposes. This sensor also must be wired to a hardwire zone.

Installing the Control's Circuit Board

To install the circuit board in the cabinet, perform the following steps:

Step Action

1

Hang the three mounting clips on the raised cabinet tabs. Refer to

Figure 3-3

(Detail B).

Make sure the clip orientation is exactly as shown in the diagram to avoid damage. This will also avoid
problems with insertion and removal of the PC board.

2

Insert the top of the circuit board into the slots at the top of the cabinet. Make certain that the board rests in
the slots as indicated (Detail A).

3

Swing the base of the board into the mounting clips and secure the board to the cabinet with the
accompanying screws.

NOTES:

•

Make certain that the mounting screws are tight. This ensures that there is a good ground connection between the
PC board and the cabinet.

•

Dress field wiring away from the microprocessor (center) section of the PC board. Use the loops on the left and right
sidewalls of the cabinet for anchoring field wiring using tie wraps (Detail C). These steps are important to minimize
the risk of panel RF interference with television reception.

+

+

+

DETAIL C

SIDE VIEW

OF SLOTS

DETAIL A

SIDE VIEW OF
BOARD INSERTED
INTO SLOTS

DETAIL B

SIDE VIEW OF SHORT
MOUNTING CLIPS
(TYP.)

hi_end_mnt-PCB

Figure 3-3: Mounting the PC Board

«
...
20
21
22
23
24
...
»

Summary of Contents for VISTA-128BPEN

































































































































Reviews:

No comments

Related manuals for VISTA-128BPEN

Brand: U-Prox Pages: 3

Brand: U-Prox Pages: 2

Brand: Z-Wave Pages: 13

Brand: FAAST Pages: 12

Brand: Memorex Pages: 2

Brand: Wheelock Pages: 10

Brand: Gallagher Pages: 67

Brand: HÜRNER Pages: 33

Brand: DAPAudio Pages: 12

Brand: Walter Pages: 132

Power2 S-MIG 100

Brand: STAMOS Pages: 33

Brand: Altec Lansing Pages: 1

Brand: JBL Pages: 4

Brand: Chuango Pages: 52

Brand: Neilsen Pages: 8

Brand: NA-DE Pages: 2

Sportsound SSR-300

Brand: Daktronics Pages: 6

Brand: Creative Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands