manualshive.com logo in svg

Honeywell VISTA-128BPEN, Installation And Setup Manual, Page: 4 / 128

Share
Download
Honeywell VISTA-128BPEN Installation And Setup Manual Download Page 4

Table of Contents

 

iv 

SECTION 5

...........................................................................................................................................................5-1

 

Data Field Descriptions ........................................................................................................................................5-1

 

About Data Field Programming ..........................................................................................................................................5-1

 

Programming Data Fields...................................................................................................................................................5-1

 

SECTION 6

...........................................................................................................................................................6-1

 

Scheduling Options ..............................................................................................................................................6-1

 

Time Window Definitions....................................................................................................................................................6-2

 

Open/Close Schedules Definitions .....................................................................................................................................6-3

 

Scheduling Menu Mode......................................................................................................................................................6-4

 

Time Windows....................................................................................................................................................................6-5

 

Daily Open/Close Schedules..............................................................................................................................................6-6

 

Holiday Schedules..............................................................................................................................................................6-6

 

Time-Driven Events............................................................................................................................................................6-7

 

Limitation of Access Schedules........................................................................................................................................6-11

 

Temporary Schedules ......................................................................................................................................................6-12

 

User Scheduling Menu Mode ...........................................................................................................................................6-14

 

SECTION 7

...........................................................................................................................................................7-1

 

Downloading Primer .............................................................................................................................................7-1

 

General Information............................................................................................................................................................7-1

 

Unattended Download........................................................................................................................................................7-1

 

Getting On-Line with a Control Panel .................................................................................................................................7-3

 

Scheduled Download .........................................................................................................................................................7-4

 

Direct-Wire Downloading....................................................................................................................................................7-4

 

Telco Handoff.....................................................................................................................................................................7-4

 

SECTION 8

...........................................................................................................................................................8-1

 

Setting the Real-Time Clock.................................................................................................................................8-1

 

General Information............................................................................................................................................................8-1

 

Setting the Time and Date..................................................................................................................................................8-1

 

SECTION 9

...........................................................................................................................................................9-1

 

User Access Codes ...............................................................................................................................................9-1

 

General Information............................................................................................................................................................9-1

 

User Codes & Levels of Authority ......................................................................................................................................9-1

 

Multiple Partition Access ....................................................................................................................................................9-2

 

Adding a Master, Manager, or Operator Code ...................................................................................................................9-3

 

Changing a Master, Manager, or Operator Code ...............................................................................................................9-4

 

Adding an RF Key to an Existing User ...............................................................................................................................9-4

 

Deleting a Master, Manager, or Operator Code .................................................................................................................9-4

 

Exiting the User Edit Mode.................................................................................................................................................9-4

 

SECTION 10

.......................................................................................................................................................10-1

 

Testing the System .............................................................................................................................................10-1

 

Battery Test......................................................................................................................................................................10-1

 

Dialer Test........................................................................................................................................................................10-1

 

Burglary Walk-Test (Code + [5] TEST).............................................................................................................................10-1

 

Armed Burglary System Test ...........................................................................................................................................10-1

 

Testing Wireless Transmitters..........................................................................................................................................10-2

 

Smoke Detector Test........................................................................................................................................................10-3

 

Trouble Conditions ...........................................................................................................................................................10-3

 

To the Installer .................................................................................................................................................................10-3

 

APPENDIX A

....................................................................................................................................................... A-1

 

Regulatory Agency Statements .......................................................................................................................... A-1

 

UL Installation Requirements ............................................................................................................................................ A-1

 

UL609 Local Mercantile Premises/Local Mercantile Safe & Vault..................................................................................... A-1

 

UL365 Police Station Connected Burglar Alarm................................................................................................................ A-1

 

UL611/UL1610 Central Station Burglary Alarm................................................................................................................. A-2

 

California State Fire Marshal (CSFM) and UL Residential Fire Battery Backup Requirements......................................... A-2

 

APPENDIX B

....................................................................................................................................................... B-1

 

Summary of System Commands ........................................................................................................................ B-1

 

APPENDIX C

....................................................................................................................................................... C-1

 

Summary of Contents for VISTA-128BPEN

































































































































Reviews:

No comments