manualshive.com logo in svg

Honeywell VISTA-128BPEN, Installation And Setup Manual

Share
Download
Honeywell VISTA-128BPEN Installation And Setup Manual Download Page 42

Vista-128BPEN Installation and Setup Guide 

3-22 

1 2 

3 

4 

5 

6 

7 

8

9

GRAY (GROUND)

YELLOW (OUT 1) 

WHITE (GROUND)

RED (OUT 2)

GREEN (GROUND)

BROWN (OUT 3)

BLUE (GROUND)

BLACK (OUT 4)

J7 CONNECTOR

IF USED.
1. OUT 1 IS NO LONGER

USABLE FOR SMOKE
DETECTOR RESET
OR GROUND START
(SEE FIELD 1*46).

2. OUT 2 & 4 CAN NO LONGER

BE USED TO PROVIDE
ALARM TRIGGERS.

N/U

4142TR CABLE

BLACK

–

AMSECO PAL-328N
PIEZO SOUNDER

+

RED

TO AUX POWER +

TERMINAL 6 

10mA CURRENT DRAIN)

J7_trigcon-001-V1

 

Figure 3-25:  Remote Keypad Sounder Wiring 

Installing the VA8200 Panel Link Module 

The VA8200 Panel Link Module (PLM) connects to the keypad (ECP) terminals on the VISTA-128BPEN and also 
connects to other PLMs via the RS-485 bus (3-wire twisted cable run). 

Figure 3-26

 is a block diagram of a panel linking 

setup using three control panels. 

 

UL

 

Panel Linking is not permitted in UL 
installations. 

 

CONTROL

PANEL

CONSOLE

PLM

CONTROL

PANEL

CONSOLE

PLM

CONTROL

PANEL

CONSOLE

PLM

ECP

ECP

ECP

RS-485

PLG-001-V0

 

Figure 3-26:  Panel Linking Block Diagram 

ECP Wire Run Limitations 

Determine wire gauge by referring to the table below. 

Wire Run Length Table

 

Wire Gauge

 

Length

 

#22 gauge 

450 feet 

#20 gauge 

700 feet 

#18 gauge 

1100 feet 

#16 gauge 

1750 feet 

 

 

•

 The 

length of the ECP wire runs combined must not exceed 2000 feet when unshielded cable is used (1000 feet

if unshielded cable is run in conduit or if shielded cable is used). 

•

 

If more than one ECP device is wired to a single run, then the above maximum lengths must be divided by the 
number of devices on the run (e.g., the maximum length is 225 feet if two keypads are wired on a #22 gauge 
run). 

 

RS-485 Bus Wire Run Limitations 

The RS-485 bus from the first Panel Linking Module to the last Panel Linking Module cannot exceed 4000 feet, using 16-
AWG twisted-pair cable.  

The recommended form of wiring is to daisy chain the connection from one unit to another. If several buildings are to be 
connected, the RS-485 bus should form a continuous path from one building to the next.  

Avoid wiring units in a star configuration, where multiple branches are formed. Star configurations create loading and 
capacitance problems that are complex, and become difficult to troubleshoot. 

Summary of Contents for VISTA-128BPEN

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands