manualshive.com logo in svg

Honeywell SmartLine RM60, Handbook

Share
Download
Honeywell SmartLine RM60 Handbook Download Page 81

 SERVICE 

7

81

SMARTLINE® RM60 (FMCW)

www.honeywell.com/ps

34-VF-25-31 iss.4 GLO December 15 US

Equipment needed (not supplied):

•

3 mm Allen wrench (for steps 1 and 4).

How to remove the back end and microwave unit

1  

Loosen the screw on the display. Open the display.

2  

Disconnect the power supply connector from the electronics block.

3  

Disconnect the display ribbon cable from the back end electronics block.

4  

Loosen the 2 screws shown in the illustration.

i

Do not loosen the other screws. You will disassemble the electronics block into 2 pieces. It 
is then difficult to remove these pieces from the housing.

5  

Remove the back end and microwave unit from the housing. Send the electronics block to an 

authorized agent for maintenance.

How to attach the back end and microwave unit

•  

Open the display.

•  

Put the  electronics block into the housing. Make sure that the wave guide engages in the 

mating part.

•  

Tighten the 2 screws to attach the electronics block to the bottom of the housing.

•  

Connect the display ribbon cable to the back end electronics block.

•  

Connect power supply connector to the back end electronics block.

•  

Close the display. Tighten the screw on the display.

Summary of Contents for SmartLine RM60

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands