Honeywell SmartLine RM60 Handbook Download Page 31

Page: 31 / 128

INSTALLATION

SMARTLINE® RM60 (FMCW)

www.honeywell.com/ps

34-VF-25-31 iss.4 GLO December 15 US

Use the display screen or HART

communication (PACTware

™

). Antenna extension =

antenna extension length × number of extensions.

•

If you changed the antenna extension value in Supervisor

Supervisor

Supervisor mode, also change the blocking

distance value. Go to Supervisor > Advanced setup > Installation > Blocking Distance

Supervisor > Advanced setup > Installation > Blocking Distance

Supervisor > Advanced setup > Installation > Blocking Distance.

Use the display screen or HART

communication (PACTware

™

). Minimum blocking

distance = antenna (antenna extension length × number of extensions) + 0.3 m /
12

3.7.4 How to turn or remove the signal converter

INFORMATION!

The converter turns 360

. The converter can be removed from the process connection assembly

under process conditions.

Figure 3-14: How to turn or remove the signal converter

Tool: 5 mm Allen wrench (not supplied)

Cover for the wave guide hole on top of the process connection assembly (not supplied)

CAUTION!

If you remove the converter, put a cover on the wave guide hole on top of the process connection
assembly.
When the converter is attached to the process connection assembly, tighten the lock screw.

Summary of Contents for SmartLine RM60

































































































































Search results

Summary of Contents for SmartLine RM60

Reviews:

Brands by name

Popular brands

Honeywell SmartLine RM60, Handbook

Search results

Summary of Contents for SmartLine RM60

Reviews:

Brands by name

Popular brands