manualshive.com logo in svg

Honeywell SmartLine RM60, Handbook

Share
Download
Honeywell SmartLine RM60 Handbook Download Page 107

 DESCRIPTION OF HART INTERFACE 

9

107

SMARTLINE® RM60 (FMCW)

www.honeywell.com/ps

34-VF-25-31 iss.4 GLO December 15 US

9.4  HART

®

 device variables

The HART

®

 dynamic variables PV (Primary Variable), SV (Secondary Variable), TV (Third Variable) 

and QV (Fourth Variable) can be assigned to any of the device variables.

The HART

®

 dynamic variable PV is always connected to the HART

®

 current output which is, for 

example, assigned to level measurement.

9.5  Field Communicator 375/475 (FC 375/475)

The Field Communicator is a hand terminal from Emerson Process Management that is 
designed to configure HART

®

 and Foundation Fieldbus devices. Device Descriptions (DDs) are 

used to integrate different devices into the Field Communicator.

9.5.1  Installation

System and software requirements for the Field Communicator

•

System card that includes the "Easy Upgrade Option"

•

Field Communicator Easy Upgrade Programming Utility

•

HART

®

 Device Description file

For more data, refer to the Field Communicator User

’

s Manual.

9.5.2  Operation

The Field Communicator and the device's local display use almost the same procedures to 
operate the signal converter. The online help for each menu item refers to the function number 
given to each menu item on the local device display. Protection of settings is the same as on the 
device's local display.

The Field Communicator always saves a complete configuration for communication with AMS.

HART

®

 device variable

Code

Type

level

0

linear

distance

1

linear

level conversion

2

linear

level mass

3

linear

reflection

4

linear

distance conversion

5

linear

distance mass

6

linear

CAUTION!

The Field Communicator cannot be used to correctly configure, operate or read data from the 
device unless the Device Description (DD) file is installed.

INFORMATION!

The Field Communicator will not give you access to the service menu. A simulation is only 
possible for current outputs.

Summary of Contents for SmartLine RM60

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands