manualshive.com logo in svg

Honeywell SmartLine RM60, Handbook

Share
Download
Honeywell SmartLine RM60 Handbook Download Page 79

 SERVICE 

7

79

SMARTLINE® RM60 (FMCW)

www.honeywell.com/ps

34-VF-25-31 iss.4 GLO December 15 US

Equipment needed (not supplied):

•

TORX T8 wrench.

•

3 mm Allen wrench (for steps 2 and 4).

How to remove the display

1  

Remove the 2 small screws on the hinge of the gray sun cover with a TORX T8 wrench. Remove 

the sun cover.

2  

Loosen the screw on the display screen cover. Open the display.

3  

Disconnect the ribbon cable from the back end electronics block.

i

Keep the ribbon cable connected to the display screen cover.

4  

Remove the 2 screws that keep the display attached to the housing.

5  

Keep the remaining assembly and put it into storage. Make sure that the top of the housing 

has a protective cover.

6  

Send the display to an authorized agent for maintenance.

How to attach the display

•  

Attach the display. Attach the 2 housing screws.

•  

Connect the ribbon cable to the back end electronics block.

i

Make sure the connector is correctly turned. Do not use force to connect the ribbon cable.

•  

Close the display. Tighten the screw on the display.

•  

Attach the sun cover. Attach the 2 small screws that keep the sun cover attached to the 

housing.

WARNING!

Disconnect the power supply

Summary of Contents for SmartLine RM60

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands