Honeywell OW-CDX050 User Manual Download | Manualshive

Page: 18 / 134

background image

Agency compliance information

Compliance statements and restrictions

6

OneWireless Multinode User's Guide

R110

6/08

Radio Frequency (RF) statement

To comply with FCC’s and Industry Canada’s RF exposure requirements, the following
antenna installation and device operating configurations must be satisfied.

•

Remote Point-to-Multi-Point antenna(s) for this unit must be fixed and mounted on
outdoor permanent structures with a separation distance between the antenna(s) of
greater than 20cm and a separation distance of at least 20cm from all persons.

•

Remote Fixed Point-to-Point antenna(s) for this unit must be fixed and mounted on
outdoor permanent structures with a separation distance between the antenna(s) of
greater than 20cm and a separation distance of at least 100cm from all persons.

•

Furthermore, when using integral antenna(s) the Multinode unit must not be co-
located with any other antenna or transmitter device and have a separation distance
of at least 20cm from all persons.

European Union restriction

France restricts outdoor use to 10mW (10dBm) EIRP in the frequency range of 2,454-
2,483.5 MHz. Installations in France must limit EIRP to 10dBm, for operating modes
utilizing frequencies in the range of 2,454 - 2,483.5MHz.

«
...
16
17
18
19
20
...
»

Summary of Contents for OW-CDX050







































































































































Reviews:

No comments

Related manuals for OW-CDX050

Brand: RTA Pages: 66

Brand: XAVi Pages: 51

Brand: ADTRAN Pages: 2

Brand: ADTRAN Pages: 30

Brand: Gree Pages: 31

Brand: SpectraLink Pages: 35

Brand: ECKELMANN Pages: 34

MiBoxer ZB-Box2

Brand: Mi-Light Pages: 6

Brand: Innoband Pages: 87

SC10E4IM Series

Brand: San Telequip Pages: 65

Brand: Eyedro Pages: 2

Brand: Wildix Pages: 11

Brand: Zycoo Pages: 15

Brand: Zycoo Pages: 22

HomePortal 5011NV

Brand: 2Wire Pages: 18

Brand: Eelectron Pages: 9

Brand: Teltonika Pages: 6

Brand: Kiwi Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands