manualshive.com logo in svg

Honeywell OW-CDX050, User Manual

Share
Download
Honeywell OW-CDX050 User Manual Download Page 20

Agency compliance information 

Honeywell Declaration of Conformity information 

8 

  OneWireless Multinode User's Guide  

R110 

  

6/08 

 

Honeywell Declaration of Conformity information 

This section contains the Declaration of Conformity (DoC) statement for the Multinode 
device and the countries it is intended to be used in. For a complete list of compliant 
models, contact Honeywell. 

Multinode device DoC statement 

Following is Honeywell’s Declaration of Conformity (DOC) for the OneWireless 
Multinode Device.   

R&TTE 
Directive 

1999/5/EC 

LVD  

Directive

73/23/EEC

EMC 
Directive

2004/108/EC 

ATEX  

Directive

 

94/9/EC

Harmonized Standards 

Emissions Specification and Method: EN 300 328 V1.7.1  

Emissions Spec and Method: EN 301 893 V1.4.1  

Immunity Specification:  EN 301 489-17 V1.2.1 

Immunity Method:  EN 301 489-1 V1.6.1  

Product Standard: IEC61326-1 (1

st

 Edition, 2002-02, Industrial Locations)  

EN 50014:1992, "Electrical Apparatus for Potentially Explosive Atmospheres –  
General Requirements" 

EN 50021:1999, "Electrical Apparatus for Potentially Explosive Atmospheres –  
Type of Protection "n"  

Manufacturer’s Name 
and Address 

Honeywell Process Solutions  

2500 West Union Hills Drive, Phoenix, AZ 85027, USA 

Compliance 
Statement 

The product herewith complies with the harmonized standards listed 
above. Typical product line systems and configurations have been 
tested, for compliance. 

 

 

Summary of Contents for OW-CDX050







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands