Honeywell OW-CDX050 User Manual Download Page 119

Page: 119 / 134

Multinode Operation and Monitoring

Monitoring/Reports screens

R110

OneWireless Multinode User's Guide

107

6/08

Statistic

Description

Network Interface Status

WAN Ethernet MAC Address:

The MAC address of the WAN card

LAN Ethernet MAC Address:

The MAC address of the Local Access Network
(LAN) card in the multinode.

Primary WLAN MAC Address:

The MAC address of the primary Wireless LAN
card in the multinode.

Secondary WLAN MAC
Address:

The MAC address of the secondary Wireless LAN
card in the multinode.

Routing Table

Dest. LAN IP:

Subnet Mask

Default Gateway

Hop Count

Interface

Mesh Protocol Status

Click on the Monitoring Reports - Mesh Protocol Status at the left of the screen to call up
the Mesh Protocol Status screen and provides the statistics of the wireless mesh network,
such as:

•

Ethernet Port STP Status

•

Wireless Port 0 STP Status

•

Wireless Mesh Information

Summary of Contents for OW-CDX050







































































































































Search results

Summary of Contents for OW-CDX050

Reviews:

Related manuals for OW-CDX050

Brands by name

Popular brands

Honeywell OW-CDX050, User Manual

Search results

Summary of Contents for OW-CDX050

Reviews:

Related manuals for OW-CDX050

Brands by name

Popular brands