manualshive.com logo in svg

Honeywell HTRD400, Reference Manual, Page: 41 / 176

Share
Download
Honeywell HTRD400 Reference Manual Download Page 41

Rev 1.02

27

Document 900.0328

05/05

3

HTRD BusView™ Toolbox and BusView™ 
Player Installation

This chapter describes how to install the HTRD BusView Toolbox and HTRD BusView 
Player Installation software on a PC or laptop.

Note

In this chapter:

•

The term PC refers to either a PC or a laptop.

•

BusView Toolbox and BusView Player are referred to as Toolbox and 
Player

General Software Installation Procedure

Note

To ensure that you can read, write, and modify BusView data files and 

application support files, we recommend that all BusView users be 
administrator group members of your Microsoft® Windows® 2000, 
XP Professional, or XP Home operating system.

You must be logged in to Windows 2000, XP Professional, or XP 
Home with administrator privileges to install BusView software. Also, 
all additional users should be logged off.

To ensure maximum system performance, make sure that you complete each step in the 
proper sequence:

❏

1. Check your PC for minimum system 

requirements.

See 

PC System Requirements

, 

page 

28

.

❏

2. Install the Toolbox and Player software 

on your PC.

See 

Installing the Toolbox and 

Player Software

, page 

29

.

Summary of Contents for HTRD400

















































































































































































Reviews:

No comments