Honda NHSO aeroBO 1983 Shop Manual Download Page 103

Page: 103 / 184

HONDA

NHSO

Drive a new journal bearing into the right crankcase.

Drive a new journal bearing into the left crankcase.

Install the crankshaft into the

left

crankcase.

Position Collar (07965-GC701 00) with the small

O.D. against the crankshaft bearing.

Thread the bolt from Assembly Tool (07965-

1480200) onto the crankshaft.

Hold the bolt and turn the nut clockwise to fully

install the crankshaft.

lubricate the crankshaft main and journal bearings

with Honda 2-stroke oil or equivalent.

Date of Issue: May, 1983

ATTACHMENT, 42

47 mm

07746-0010300

ASSEMBLY TOOL

CRANKCASE/CRANKSHAFT

DRIVER

077 49-001 0000

PI LOT, 25 mm

077 46-0040600

DRIVER

077 49-0010000

PILOT, 25 mm

077 46-0040600

07965-1480200 ( NC. IN 07965-GC70000)

ASSEMBLY COLLAR

07965-GC70100 (INC. IN 07965-GC70000)

109

1 0- 5

Summary of Contents for NHSO aeroBO 1983

























































































































































































Search results

Summary of Contents for NHSO aeroBO 1983

Reviews:

Related manuals for NHSO aeroBO 1983

Brands by name

Popular brands

Honda NHSO aeroBO 1983, Shop Manual

Search results

Summary of Contents for NHSO aeroBO 1983

Reviews:

Related manuals for NHSO aeroBO 1983

Brands by name

Popular brands