Honda NHSO aeroBO 1983 Shop Manual Download Page 174

Page: 174 / 184

TECHNICAL FEATURES

DRIVE PULLEY

WEIGHT ROLLER

DRIVE FACE

HONDA

NH80

The drive pulley consists of a fixed face and a movable face. The movable face is capable of sliding axially on the boss of the

fixed face. The ramp plate, which pushes in the weight rollers against the drive face, is attached to the boss of the drive face

with a nut.

DRIVE BELT

MOVABLE FACE

ASSPEED INCREASES

RAMP PLATE

WEIGHT ROLLER

As the speed of the engine increases, centrifugal force on the weight rollers is also increased. This pushes the movable drive face

inward. The unit then acts with a reduced drive ratio by allowing the drive belt to run on a pulley of greater diameter.

1 7 -4

184

Date of Issue: May, 1983

Summary of Contents for NHSO aeroBO 1983

























































































































































































Search results

Summary of Contents for NHSO aeroBO 1983

Reviews:

Related manuals for NHSO aeroBO 1983

Brands by name

Popular brands

Honda NHSO aeroBO 1983, Shop Manual

Search results

Summary of Contents for NHSO aeroBO 1983

Reviews:

Related manuals for NHSO aeroBO 1983

Brands by name

Popular brands