Honda NHSO aeroBO 1983 Shop Manual Download Page 139

Page: 139 / 184

ASSEMBLY

Apply grease to the anchor contacting area of the

brake cam.

Apply grease to the brake cam, and install.

Install the brake shoes.

Install the wear indicator plate.

NOTE:

Align the wide groove on the cam with the

wide tooth on the indicator plate.

Install the brake arm.

NOTE:

Align the scribed lines on the brake cam and

brake arm.

Tighten the brake arm bolt to the specified torque.

TORQUE: 4-7

N·m

(0.4-0.7

kg·m,

3-5

ft·lb)

Install the brake arm spring.

Date of Issue: May, 1 983

©HONDA MOTOR CO., LTD.

REAR WHEE L/BRAKE/SUSPENSION

BRAKE CAM

SCRIBED LINES

BRAKE CAM

BRAKE ARM

BRAKE ARM SPRING

149

1 3- 5

Summary of Contents for NHSO aeroBO 1983

























































































































































































Search results

Summary of Contents for NHSO aeroBO 1983

Reviews:

Related manuals for NHSO aeroBO 1983

Brands by name

Popular brands

Honda NHSO aeroBO 1983, Shop Manual

Search results

Summary of Contents for NHSO aeroBO 1983

Reviews:

Related manuals for NHSO aeroBO 1983

Brands by name

Popular brands