Honda NHSO aeroBO 1983 Shop Manual Download Page 161

Page: 161 / 184

ELECTRICAL

EQUIPMENT

lubricate the starter pinion with clean grease.

Install the pinion and starter cover.

lubricate the gear on the starter body and install

the starter motor cover on the body.

Connect the starter wires.

STARTER MOTOR INSTALLATION

NOTE:

Before installing the starter, test for operation

by connecting the starter coupler to the wire

harness.

Install the starter motor in the reverse order of re

moval.

Secure the wires with the wire clamps.

Install the engine (Section

5).

1 5 - 1 4

172

STARTER COVER

STARTER BODY

HONDA

NHSO

PINION GEAR

STARTER COVER

STARTER WIRES

Date of Issue: May, 1983

TO.

Summary of Contents for NHSO aeroBO 1983

























































































































































































Search results

Summary of Contents for NHSO aeroBO 1983

Reviews:

Related manuals for NHSO aeroBO 1983

Brands by name

Popular brands

Honda NHSO aeroBO 1983, Shop Manual

Search results

Summary of Contents for NHSO aeroBO 1983

Reviews:

Related manuals for NHSO aeroBO 1983

Brands by name

Popular brands