manualshive.com logo in svg

Hitachi H8S/2215 Series, Hardware Manual

The Hitachi H8S/2215 Series Hardware Manual is an essential resource for users wanting detailed instructions on operating and maximizing the potential of their Hitachi H8S/2215 Series device. Download this comprehensive manual for free from manualshive.com and unlock the full potential of your product.

Share
Download
background image

Rev. 3.0, 10/02, page 200 of 686

8.2.8

DTC Vector Register (DTVECR)

DTVECR enables or disables DTC activation by software, and sets a vector number for the
software activation interrupt.

Bit

Bit Name Initial Value

R/W

Description

7

SWDTE

0

R/W

DTC Software Activation Enable

Setting this bit to 1 activates DTC. The write value should
always be 1.

[Clearing conditions]

•

 

When the DISEL bit is 0 and the specified number of

transfers have not ended

•

 

When 0 s written to the DISEL bit after a software-

activated data transfer end interrupt (SWDTEND)

request has been sent to the CPU.

When the DISEL bit is 1 and data transfer has ended or
when the specified number of transfers have ended, this
bit will not be cleared.

6

5

4

3

2

1

0

DTVEC6

DTVEC5

DTVEC4

DTVEC3

DTVEC2

DTVEC1

DTVEC0

0

0

0

0

0

0

0

R/W

R/W

R/W

R/W

R/W

R/W

R/W

DTC Software Activation Vector 6 to 0

These bits specify a vector number for DTC software
activation.

The vector address is expressed as H'0400 + (vector
number × 2). For example, when DTVEC6 to
DTVEC0 = H'10, the vector address is H'0420. When the
bit SWDTE is 0, these bits can be written.

Summary of Contents for H8S/2215 Series










































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S/2215 Series

XDS 910 Reference Manual preview
910
Brand: XDS Pages: 99
Raidon SAFETank Series User Manual preview
SAFETank Series
Brand: Raidon Pages: 49
Safety Vision ROADRECORDER 8000 User Manual preview
ROADRECORDER 8000
Brand: Safety Vision Pages: 40
Dahua DHI-NVR2104-P-4KS2 Quick Start Manual preview
DHI-NVR2104-P-4KS2
Brand: Dahua Pages: 23
Idis DR-8400 Installation Manual preview
DR-8400
Brand: Idis Pages: 31
IDT USB-BRIDGEV2-EVAL Evaluation Board Manual preview
USB-BRIDGEV2-EVAL
Brand: IDT Pages: 11
Novus NVIP- NVRA0104/GO User Manual preview
NVIP- NVRA0104/GO
Brand: Novus Pages: 44
Lindsay Broadband LBON320AC Series Installation And Operation Manual preview
LBON320AC Series
Brand: Lindsay Broadband Pages: 4
Bridgeworks Oresund EFC102200 User Manual preview
Oresund EFC102200
Brand: Bridgeworks Pages: 84
Xantech CC12 Installation Instructions preview
CC12
Brand: Xantech Pages: 4
AXIOMTEK CEM820 Series User Manual preview
CEM820 Series
Brand: AXIOMTEK Pages: 58
Trend Micro IPS Pro-Module-24C-GE-BP-TM Quick Setup Manual preview
IPS Pro-Module-24C-GE-BP-TM
Brand: Trend Micro Pages: 3
Dahua NVRPRO User Manual preview
NVRPRO
Brand: Dahua Pages: 113
Alcatel-Lucent 9364 Installation And Commissioning Manual preview
9364
Brand: Alcatel-Lucent Pages: 60
Uctronics U6180 Instruction Manual preview
U6180
Brand: Uctronics Pages: 2
Vivint AirBridge VS-YOFIMN-000 Quick Reference preview
AirBridge VS-YOFIMN-000
Brand: Vivint Pages: 2
Tripp Lite B078-001-USB Specification preview
B078-001-USB
Brand: Tripp Lite Pages: 2
Aetina Nvidia Jetson Series Quick Start Manual preview
Nvidia Jetson Series
Brand: Aetina Pages: 7

Brands by name

Popular brands

Load more brands