manualshive.com logo in svg

Hioki ST5520, Instruction Manual, Page: 179 / 201

Share
Download
Hioki ST5520 Instruction Manual Download Page 179

171

Troubleshooting

Error display and solutions

The following messages are displayed on the screen when there is a problem with the 

instrument or measurement.

If repair is required, contact your authorized Hioki distributor or reseller.

 

• If any damage is suspected, check “Troubleshooting” first and then contact your authorized 

Hioki distributor or reseller.

 

• If an error is displayed in the LCD display and repair is required, contact your authorized Hioki 

distributor or reseller.

Display

Meaning

Solution

Reference 

ContHL

Contact check 

error

Check the wiring of the 

measurement cable for the contact 

check.

p. 56

Check the contact check function.

p. 29

ContHi

HIGH side 

contact check 

error

Check the wiring of the 

measurement cable for the HIGH 

side contact check.

p. 56

Check the contact check function.

p. 29

ContLo

LOW side contact 

check error

Check the wiring of the 

measurement cable for the LOW 

side contact check.

p. 56

Check the contact check function.

p. 29

Short

Short circuit 

check error

The equipment to be measured 

may be short-circuited. Check the 

equipment to be measured.

p. 60

ERR:001

LOW limit is 

higher than 

UPP limit.

The upper limit 
value cannot be 
set because the 
lower limit value 
is greater than 
the upper limit 

value.

Set the upper limit value so it is 

greater than the lower limit value.

p. 44

ERR:002

Double action 

is ON. Press 

[STOP] first 

and press 

[START] 

within 1 sec 

to start.

Double action 
error

The double action function is set to 

ON.

p. 68

ERR:003

Delay time is 
longer than 

test time.

Test duration 
error

The response time is set longer 

than the test duration.

p. 39

10

9

8

7

6

5

4

3

2

1

Appx.

Ind.

Summary of Contents for ST5520










































































































































































































Reviews:

No comments