manualshive.com logo in svg

Hioki ST5520, Instruction Manual, Page: 186 / 201

Share
Download
Hioki ST5520 Instruction Manual Download Page 186

Appx.

6

Influence of Cable Length

Appx. 5 

Influence of Cable Length

When the instrument is incorporated in a production line or automated machine, the 
measurement cable may be extended. When the measurement cable is extended, 
measured values can be affected by coupling capacitance between cables or line 

noise. The level of influence on measured values when the measurement cable is 

extended is shown below.

For the influence of a capacitive load, refer to “Appx. 4 Influence of Capacitive Load” 

(p. Appx.4). For the influence of line noise, refer to “Appx. 6 Influence of Noise” (p. Appx.7).

Cable: 

UL1032  AWG18

 

Twisted wires  75 wires × 

f

0.12 mm (extended optional L2200)

Instrument settings

Test voltage: 

1000 V

Resistance range:  4000 M

Ω

 range

Load: 

3600 M

Ω

 + cable coupling capacitance (approx. 250 pF)

Cable length

Measurement  
speed

0.7 m

2 m

3 m

4 m

FAST

±0.1%

±0.4%

±0.7%

±0.9%

SLOW

±0.1%

±0.4%

±0.6%

±0.8%

The values above indicate the repeat accuracy.

Cautions for measurement cable wiring

 

• When the measurement cable is laid on a metal ground, the influence of noise can be reduced.

 

• When the measurement cable is extended, the influence of power line noise becomes more 

significant. Position the measurement cable away from the power line.

 

•

Position the measurement cable away from any noise sources (motor, welder, inverter, etc.).

Summary of Contents for ST5520










































































































































































































Reviews:

No comments