Hioki ST5520 Instruction Manual Download Page 19

Page: 19 / 201

Usage Notes

Before connecting switched probes

CAUTION

To avoid damage to the probes, do not bend or pull the probe base.

To ensure safe operation, use only the probes specified by our company.

Residual risk

WARNING

The test leads generate high voltage. To avoid electric shock, do not
touch the metal ends of the test leads.

CAUTION

The ends of the probes are sharp. Be careful to avoid injury.

Before connecting data cables

WARNING

•

Failure to fasten the connectors properly may result in sub-

specification performance or damage to the equipment.

•

Always turn off both devices when connecting and disconnecting
an interface connector. Otherwise, an electric shock accident may
occur.

Before switching between current sink (NPN) and current source (PNP)

CAUTION

Do not operate the EXT.I/O mode switch (NPN/PNP) while the instrument is
on.

Configure the NPN/PNP setting to accommodate externally connected

equipment.

Appx.

Ind.

Summary of Contents for ST5520










































































































































































































Search results

Summary of Contents for ST5520

Reviews:

Hioki ST5520, Instruction Manual, Page: 19 / 201

Search results

Summary of Contents for ST5520

Reviews: