manualshive.com logo in svg

Hioki ST5520, Instruction Manual, Page: 149 / 201

Share
Download
Hioki ST5520 Instruction Manual Download Page 149

141

Command Reference

:KEY:BEEPer

Sets the key beep sound ON/OFF.

Syntax

:KEY:BEEPer <data>

<data>

ON/OFF (text data)

Example

To set the key beeper to sound
PC>

 :KEY:BEEPer ON

:KEY:BEEPer?

Queries the key beep sound ON/OFF setting. The beep sound ON/OFF setting is returned in 

text data (<data>).

Syntax

:KEY:BEEPer?

Response

:KEY:BEEPER <data>

 or simply 

<data>

<data>

ON/OFF (text data)

Example

To query the key beep sound ON/OFF setting (when the setting is ON)

PC>

:KEY:BEEPer?

ST5520>

:KEY:BEEPER ON

  (when the 

:HEADer

 command is ON)

ST5520>

ON

 

 

(when the 

:HEADer

 command is OFF)

:DOUBleaction

Sets the double action function ON/OFF.

Syntax

:DOUBleaction <data>

<data>

ON/OFF (text data)

ON: The double action function is enabled.

OFF: The double action function is disabled.

Example

To set the double action function to ON

PC> 

:DOUBleaction ON

:DOUBleaction?

Queries the double action function ON/OFF setting. The setting is returned in text data (<data>).

Syntax

:DOUBleaction?

Response

:DOUBLEACTION <data>

 or simply 

<data>

<data>

ON/OFF (text data)

ON: The double action function is enabled.

OFF: The double action function is disabled.

Example

To query the double action function setting (when the setting is ON)

PC>

:DOUBleaction?

ST5520>

:DOUBLEACTION ON

   (when 

the 

:HEADer

 command is ON)

ST5520>

ON

 

 

(when the 

:HEADer

 command is OFF)

10

9

8

7

6

5

4

3

2

1

Appx.

Ind.

Summary of Contents for ST5520










































































































































































































Reviews:

No comments