manualshive.com logo in svg

Hioki ST5520, Instruction Manual, Page: 35 / 201

Share
Download
Hioki ST5520 Instruction Manual Download Page 35

27

Pre-Operation Inspection

2.5  Pre-Operation Inspection

Before using the instrument the first time, check that it operates normally to ensure 

that no damage occurred during storage or shipping. If any damage is found, 

contact your authorized Hioki distributor or reseller.

Accessory and optional equipment inspection

Check item

Action

Is the power cord coating ripped or torn, or is 

any metal exposed?

Do not use the instrument if damage is found, 
as electric shock or short circuit accidents 
could result.

Contact your authorized Hioki distributor or 

reseller.

Is the probe coating ripped or torn, or is any 

metal exposed?

Replace the probes with those specified by 

our company if damage is found, as electric 

shock could result.

Instrument inspection

Check item

Action

Is there any damage to the instrument?

If damage is found, send out the instrument 
for repair.

Insulation resistance test inspection

To ensure safe operation of the instrument, check the following before starting 

measurements.

 

• Checking the insulation resistance test (p. 28)

Check that the measured resistance matches the resistance value of the prepared 
resistor.

 

• Checking the contact check function (p. 29)

Check that the contact check function operates properly.

10

9

8

7

6

5

4

3

2

1

Appx.

Ind.

Summary of Contents for ST5520










































































































































































































Reviews:

No comments