manualshive.com logo in svg

Hioki ST5520, Instruction Manual, Page: 141 / 201

Share
Download
Hioki ST5520 Instruction Manual Download Page 141

133

Command Reference

:MEASure:CLEar

Clears measured value and judgment result.

The status is changed so that no judgment has been made.

Syntax

:MEASure:CLEar

Example

To clear the measured value and judgment result

PC>

:MEASure:CLEar

:MEASure:MONItor?

Queries the voltage monitor value. The rvoltage monitor value is returned in NR1 numerical data 

(<data>) 

No command header is included in response.

Syntax

:MEASure:MONItor?

Response

:<data>

<data>

Voltage monitor value (unit: V)  0 to 1000 (resolution 1V) (NR1)

Example

To query the voltage monitor value (when the voltage monitor value is 25 V)

PC>

:MEASure:MONItor?

ST5520>

25

:VOLTage

Sets the test voltage.
When the testing start command, 

:STARt

 is sent sequentially after the test voltage is changed, 

a time of up to 500 ms is added until the test starts.

Syntax

:VOLTage <data>

<data>

Test voltage 

25 to 1000 (NR1 numerical data)

Example

To set the test voltage to 100 V

PC>

:VOLTage 100

:VOLTage?

Queries the test voltage. The test voltage is returned in NR1 numerical data (<data>).

Syntax

:VOLTage?

Response

:VOLTAGE <data>

 or simply 

<data>

<data>

Test voltage 

25 to 1000 (NR1 numerical data)

Example

To query the test voltage (when the test voltage is 100 V)

PC>

:VOLTage?

ST5520>

:VOLTAGE 100

 

(when the 

:HEADer

 command is ON)

ST5520>

100

 

 

(when the 

:HEADer

 command is OFF)

10

9

8

7

6

5

4

3

2

1

Appx.

Ind.

Summary of Contents for ST5520










































































































































































































Reviews:

No comments