Hioki ST5520 Instruction Manual Download Page 174

Page: 174 / 201

166

Maintenance

Replacement parts and lifetime

Some of the parts used for this instrument may deteriorate due to an extended period

of use.

It is recommended to replace the parts so that the instrument can be used for a long

period of time.

Contact your authorized Hioki distributor or reseller for replacement parts.

The lifetime of the parts varies depending on the operating environment and

frequency of use. The recommended replacement timing is not guaranteed.

Part name

Recommended

replacement timing

Remarks/Conditions

Electrolytic
capacitor

Approx. 10 years

The board on which the capacitor is

installed is to be replaced.

LCD backlight

Approx. 10 years

When the backlight is used for 24 hours/

day at 25 ± 5°C and 50 ± 10% RH.

Summary of Contents for ST5520










































































































































































































Search results

Summary of Contents for ST5520

Reviews:

Hioki ST5520, Instruction Manual, Page: 174 / 201

Search results

Summary of Contents for ST5520

Reviews: