manualshive.com logo in svg

Hioki ST5520, Instruction Manual, Page: 69 / 201

Share
Download
Hioki ST5520 Instruction Manual Download Page 69

61

Checking Short Circuit before Applying the Set Voltage (Short circuit check function)

IMPORTANT

 

•

If the equipment to be measured contains electrostatic capacitance components, 
t1 becomes longer. Set the time using the automatic measurement function for 
short circuit check time.

 

• The voltage to be applied fluctuates between 2 and 4 V depending on the 

equipment to be measured.

Test starts

Judgment

Short circuit check error

Insulation resistance test

Test ends

Short circuit check

Judgment OK

Judgment NG

[AUTO]

The time required for the automatic short circuit check is different between the 
correctly operating product and the short-circuited product. Each check takes 
up to 0.5 s.

[AUTO]

 is also used for checking the shortest short circuit check execution 

time.

How to check the shortest execution time

When a correctly operating product is connected and a test is started, the 

short circuit check finishes as soon as the effect of the charging current has 

disappeared, and then the time taken is displayed.
Perform this process for multiple units of the equipment to be measured, and 
then set the longest time displayed (plus a little extra time) after 

[MANUAL]

 is 

selected.
The time taken for the short circuit check is displayed at the upper right of the 
measured value display section.

[MANUAL]

[MANUAL]

 is used to execute a short circuit check in the shortest time.

The short circuit check time can be set freely in the range of 0.010 s to 1.000 s.
(When the time required for a short circuit check is unknown, it is possible to 
determine an approximate time by setting 

[SHORT CHECK TIME]

 to 

[AUTO]

 

and then performing the measurement several times. When 

[MANUAL]

 is 

selected, set the time in consideration of any variations in the characteristics 
of the measurement objects.)

10

9

8

7

6

5

4

3

2

1

Appx.

Ind.

Summary of Contents for ST5520










































































































































































































Reviews:

No comments