manualshive.com logo in svg

Hioki ST5520, Instruction Manual, Page: 49 / 201

Share
Download
Hioki ST5520 Instruction Manual Download Page 49

41

Setting the Test Duration and Response Time

Setting the response time

Response time is the time to prohibit comparator judgment after a test starts until 
the set response time elapses. No measured value is displayed during the response 
time. The response time is included in the test duration. The same response time is 
applicable at any test voltage.

Test starts

Comparator judgment starts

Response 

time

Measurement value display, 

comparator judgment

Test duration

 

•

The response time varies depending on the equipment to be measured.
If a capacitive load is connected, it may take time for the output voltage to 
rise.

 

•

When the response time is set to 

[AUTO]

, the output is monitored and the 

measurement starts after the voltage is stabilized. The time required for the 
voltage to stabilize varies depending on the equipment to be measured.

 

•

If the electrostatic capacity of the equipment to be measured is 1µF or 

more, the 

[AUTO]

 function may not operate properly because it takes time 

to charge the equipment to be measured. Check the time required for the 
value on the voltage monitor to reach the set voltage, and then set it after 

[MANUAL]

 is selected.

 

•

When the response time is set to 

[MANUAL]

, the measurement starts 

anytime. The measurement may start before the output voltage rises 
depending on the equipment to be measured. Set the response time 
according to the equipment to be measured.

During the response time, 

[D]

 is displayed to the left of the test duration 

indication on the measurement screen.

10

9

8

7

6

5

4

3

2

1

Appx.

Ind.

Summary of Contents for ST5520










































































































































































































Reviews:

No comments