manualshive.com logo in svg

Hioki ST5520, Instruction Manual, Page: 102 / 201

Share
Download
Hioki ST5520 Instruction Manual Download Page 102

94

Timing Chart

Item

Time

t1

START, STOP signal pulse width

5 ms 

MIN.

t2

START, STOP signal detection time

5 ms 

MAX.

*

t3 Response time (DELAY)

AUTO, 5 ms to 999.9 s

t4 Measurement 

time

Contact check: OFF

30 ms (FAST), 480 ms (SLOW)

Contact check: ON

80 ms (FAST), 480 ms (SLOW)

t5 Measurement 

interval

Contact check: OFF

50 ms (FAST), 500 ms (SLOW)

Contact check: ON

100 ms (FAST), 500 ms (SLOW)

t6

Discharge time (time for the output voltage to drop 

below 10 V)

20 ms 

MAX.

 (during pure resistance 

measurement)

t7 Test duration (TIMER)

45 ms to 999.9 s

*

 

When the START signal is input after the test voltage is changed, a time of up to 500 ms is 
added to detect the START signal.

Forced termination judgment mode timing chart

When the test duration setting (TIMER) is OFF and the measurement is performed by the /START 
signal or /STOP signal input from EXT.I/O or when the test duration setting (TIMER) is OFF and 
the measurement is performed by the START key or STOP key on the panel

Setting

Test duration (TIMER) Response time (DELAY)

TEST signal OFF timing

OFF

AUTO, 5 ms to 999.9 s

FAST

Summary of Contents for ST5520










































































































































































































Reviews:

No comments