Hioki ST5520 Instruction Manual Download Page 103

Page: 103 / 201

Timing Chart

10 V

/START

(Input)

/STOP

(Input)

Test voltage

Measured

value display

/PASS

(Output)

/U.FAIL

/L.FAIL

(Output)

/ERR

(Output)

t2 t6

/TEST

(Output)

Measurement end

When the TEST
signal OFF
timing setting is
SLOW

When measured

value-2 result is PASS

Previous measured value

Previous result

Measurement-1 contact check result

Measurement,

judgment

(including

contact check)

Measurement-1

Measurement-2

OFF

0/0.0/0.00 M

Measured value-1

Measured value-2

Item

Time

START, STOP signal pulse width

5 ms

MIN.

START, STOP signal detection time

5 ms

MAX.

t3 Response time (DELAY)

AUTO, 5 ms to 999.9 s

t4 Measurement

time

Contact check: OFF

30 ms (FAST), 480 ms (SLOW)

Contact check: ON

80 ms (FAST), 480 ms (SLOW)

t5 Measurement

interval

Contact check: OFF

50 ms (FAST), 500 ms (SLOW)

Contact check: ON

100 ms (FAST), 500 ms (SLOW)

Discharge time (time for the output voltage to drop

below 10 V)

20 ms

MAX.

(during pure resistance

measurement)

When the START signal is input after the test voltage is changed, a time of up to 500 ms is
added to detect the START signal.

Appx.

Ind.

Summary of Contents for ST5520










































































































































































































Search results

Summary of Contents for ST5520

Reviews:

Hioki ST5520, Instruction Manual, Page: 103 / 201

Search results

Summary of Contents for ST5520

Reviews: