manualshive.com logo in svg

Hioki ST5520, Instruction Manual, Page: 101 / 201

Share
Download
Hioki ST5520 Instruction Manual Download Page 101

93

Timing Chart

FAIL STOP mode timing chart

When the test duration setting (TIMER) is ON and the measurement is performed by the /START 
signal input from EXT.I/O or when the test duration setting (TIMER) is ON and the measurement 
is performed by the START key on the panel

Setting

Test duration (TIMER) Response time (DELAY)

TEST signal OFF timing

ON, 45 ms to 999.9 s

AUTO, 5 ms to 999.9 s

FAST

When the test duration (TIMER) is set to OFF, tests are performed continuously 
until a FAIL judgment is made.

Measurement-1

Measurement-2

10 V

t1

t2

t6

t3

t5

t4

/START

(Input)

/TEST

(Output)

Test voltage

Measured 

value display

/PASS

(Output)

/U.FAIL

/L.FAIL

(Output)

/ERR

(Output)

t7

Measurement end

When the TEST signal OFF
timing setting is SLOW

When measured 

value-1 result is PASS

When measured 

value-2 result is FAIL

Previous measured value

Previous result

Previous result

Previous result

OFF

ON

OFF

OFF

OFF

ON

OFF

0/0.0/0.00 M

Ω

Measured value-1

Measured value-2

Measurement-1 contact check result

Measurement, 

judgment

(including 

contact check)

10

9

8

7

6

5

4

3

2

1

Appx.

Ind.

Summary of Contents for ST5520










































































































































































































Reviews:

No comments