HIKVISION DS-7204HQI-K1 User Manual Download Page 87

Page: 87 / 200

DS-72xxHUI-Kx, DS-72xxHQI-Kx Digital Video Recorder (DVR) User Manual

UM DS-72xxHUI-Kx, DS-72xxHQI-Kx 062817NA

The

indicates the start time and

end time of the record files.

represents normal recording (manual or schedule).

represents event recording (motion, alarm, motion | alarm, motion

& alarm).

Playback progress bar: use the mouse to click any point of the
progress bar to locate special frames.

•

Playing Back by Event Search

Play back record files on one or several channels searched out by restricting event type
(motion detection, alarm input or VCA). Channel switch is supported.

Enter the

Playback

interface, Menu > Playback.

Click

and select

to enter the

Event Playback

interface.

Select

Alarm Input

Motion

VCA

as the event type, and specify the start time and

end time for search.

Figure 110, Video Search by Motion Detection

Click

Search

, and the record files matching the search conditions will be displayed

on a list.

Select and click

button to play back the record files.

Click

Back

to return to the search interface.

Summary of Contents for DS-7204HQI-K1









































































































































































































Search results

Summary of Contents for DS-7204HQI-K1

Reviews:

Related manuals for DS-7204HQI-K1

Brands by name

Popular brands

HIKVISION DS-7204HQI-K1, User Manual

Search results

Summary of Contents for DS-7204HQI-K1

Reviews:

Related manuals for DS-7204HQI-K1

Brands by name

Popular brands