HIKVISION DS-7204HQI-K1 User Manual Download Page 154

Page: 154 / 200

DS-72xxHUI-Kx, DS-72xxHQI-Kx Digital Video Recorder (DVR) User Manual

152

UM DS-72xxHUI-Kx, DS-72xxHQI-Kx 062817NA

Figure 190, Network Detection Interface

Select a NIC to test network delay and packet loss.

Enter the destination address in the text field of

Destination Address

Click the

Test

button to start testing network delay and packet loss.

11.3.2

Exporting Network Packet

By connecting the DVR to a network, the captured network data packet can be exported to a USB flash
disk, or other local backup device.

Enter the Network Traffic interface, Menu > Maintenance > Net Detect.

Click the

Network Detection

tab to enter the

Network Detection

interface.

Select the backup device from the

Device Name

drop-down list.

Click the

Refresh

button if the connected local backup device is not

displayed. If the system fails to detect the backup device, check
whether it is compatible with the DVR. You can format the backup
device if the format is incorrect.

Summary of Contents for DS-7204HQI-K1









































































































































































































Search results

Summary of Contents for DS-7204HQI-K1

Reviews:

Related manuals for DS-7204HQI-K1

Brands by name

Popular brands

HIKVISION DS-7204HQI-K1, User Manual

Search results

Summary of Contents for DS-7204HQI-K1

Reviews:

Related manuals for DS-7204HQI-K1

Brands by name

Popular brands