HIKVISION DS-7204HQI-K1 User Manual Download Page 155

Page: 155 / 200

DS-72xxHUI-Kx, DS-72xxHQI-Kx Digital Video Recorder (DVR) User Manual

UM DS-72xxHUI-Kx, DS-72xxHQI-Kx 062817NA

153

Figure 191, Export Network Packet

Click

Export

to start exporting.

After exporting is complete, click

to finish the packet export.

Figure 192, Packet Export Attention

Up to 1 MB of data can be exported each time.

11.3.3

Checking Network Status

You can check the network status and quickly set the network parameters in this interface.

Enter the Network Traffic interface, Menu > Maintenance > Net Detect.

Click the

Network Detection

tab to enter the

Network Detection

interface.

Click

Status

on the bottom right of the interface.

Figure 193, Checking Network Status

If the network is normal the following message box pops out:

Summary of Contents for DS-7204HQI-K1









































































































































































































Search results

Summary of Contents for DS-7204HQI-K1

Reviews:

Related manuals for DS-7204HQI-K1

Brands by name

Popular brands

HIKVISION DS-7204HQI-K1, User Manual

Search results

Summary of Contents for DS-7204HQI-K1

Reviews:

Related manuals for DS-7204HQI-K1

Brands by name

Popular brands