HIKVISION DS-7204HQI-K1 User Manual Download Page 173

Page: 173 / 200

DS-72xxHUI-Kx, DS-72xxHQI-Kx Digital Video Recorder (DVR) User Manual

UM DS-72xxHUI-Kx, DS-72xxHQI-Kx 062817NA

171

Figure 226, Copy Settings to Other Cameras

Select the camera(s) to be configured with the same OSD settings. You can also check the

Analog

checkbox to select all cameras.

Click

to finish the

Copy

settings and go back to the

OSD Configuration

interface.

Click

Apply

to apply the settings.

13.3

Configuring Privacy Mask

Configure the four-sided privacy mask zones that cannot be viewed or recorded by the operator.

Enter the

Privacy Mask Settings

interface, Menu > Cameras Setup > Privacy Mask.

Select the camera to set privacy mask.

Check the

Enable Privacy Mask

checkbox to enable this feature.

Figure 227, Privacy Mask Settings Interface

Use the

mouse

to draw a zone on the window. The zones will be marked with different frame colors.

Up to four privacy mask zones can be configured, and the size of
each area can be adjusted.

Summary of Contents for DS-7204HQI-K1









































































































































































































Search results

Summary of Contents for DS-7204HQI-K1

Reviews:

Related manuals for DS-7204HQI-K1

Brands by name

Popular brands

HIKVISION DS-7204HQI-K1, User Manual

Search results

Summary of Contents for DS-7204HQI-K1

Reviews:

Related manuals for DS-7204HQI-K1

Brands by name

Popular brands