HIKVISION DS-7204HQI-K1 User Manual Download Page 157

Page: 157 / 200

DS-72xxHUI-Kx, DS-72xxHQI-Kx Digital Video Recorder (DVR) User Manual

UM DS-72xxHUI-Kx, DS-72xxHQI-Kx 062817NA

155

Chapter 12

HDD Management

12.1

Initializing HDDs

A newly installed hard disk drive (HDD) must be initialized before it can be used with the DVR.

Enter the

HDD Information

interface, Menu > System Configuration > HDD.

Figure 197, HDD Information Interface

You can view the Total Capacity, Free Space, and Remaining
Recording Time of the HDD. The algorithm of the Remaining
Recording Time uses average bit rate for the channel enabling
smart encoding to raise accuracy.

Select the HDD to be initialized.

Click

Init

Figure 198, Confirm Initialization

Select

to start initialization.

Summary of Contents for DS-7204HQI-K1









































































































































































































Search results

Summary of Contents for DS-7204HQI-K1

Reviews:

Related manuals for DS-7204HQI-K1

Brands by name

Popular brands

HIKVISION DS-7204HQI-K1, User Manual

Search results

Summary of Contents for DS-7204HQI-K1

Reviews:

Related manuals for DS-7204HQI-K1

Brands by name

Popular brands