HIKVISION DS-7204HQI-K1 User Manual Download Page 78

Page: 78 / 200

DS-72xxHUI-Kx, DS-72xxHQI-Kx Digital Video Recorder (DVR) User Manual

UM DS-72xxHUI-Kx, DS-72xxHQI-Kx 062817NA

Figure 93, More Settings

10.

Check the

Redundant

Record

checkbox.

11.

Click

to save the settings.

12.

If the encoding parameters can also be used to other channels, click

Copy

and choose the channel to

apply the settings to.

5.9

Configuring HDD Group

You can group the HDDs and save the record files in specific HDD groups.

Enter HDD setting interface, Menu > System Configuration > HDD.

Select Storage Mode tab.

Check whether the storage mode of the HDD is Group. If not, set it to Group.

Select

General

in the left bar.

Click

to enter editing interface.

Configuring HDD group.

Choose a group number for the HDD group.

Click

Apply

to save your settings.

Click

to go back to the upper level menu.

Repeat the above steps to configure more HDD groups.

10.

Choose the Channels for which you want to save the record files in the HDD group.

11.

Enter

Storage Mode

interface, Menu>HDD>Advanced> Storage Mode.

Summary of Contents for DS-7204HQI-K1









































































































































































































Search results

Summary of Contents for DS-7204HQI-K1

Reviews:

Related manuals for DS-7204HQI-K1

Brands by name

Popular brands

HIKVISION DS-7204HQI-K1, User Manual

Search results

Summary of Contents for DS-7204HQI-K1

Reviews:

Related manuals for DS-7204HQI-K1

Brands by name

Popular brands