HIKVISION DS-7204HQI-K1 User Manual Download Page 74

Page: 74 / 200

DS-72xxHUI-Kx, DS-72xxHQI-Kx Digital Video Recorder (DVR) User Manual

UM DS-72xxHUI-Kx, DS-72xxHQI-Kx 062817NA

Figure 86, Set Triggered Camera of VCA Alarm

Enter

Record Schedule Settings

interface (Menu > Record > Schedule > Record Schedule), and then set

Event as the record type.

5.6

Configuring Manual Recording

Follow these steps to set manual recording parameters. Manual recording is prior to scheduled recording.

Enter the

Manual Record

interface, Menu > Manual.

Figure 87, Manual Record

Enable manual record.

Click

before the camera number to change it to

Or click the

Analog

status icon to enable manual record of all channels.

Disable manual record.

Click

to change it to

Or click the

Analog

status icon to disable manual record of all channels.

After rebooting, all enabled manual records are canceled.

Summary of Contents for DS-7204HQI-K1









































































































































































































Search results

Summary of Contents for DS-7204HQI-K1

Reviews:

Related manuals for DS-7204HQI-K1

Brands by name

Popular brands

HIKVISION DS-7204HQI-K1, User Manual

Search results

Summary of Contents for DS-7204HQI-K1

Reviews:

Related manuals for DS-7204HQI-K1

Brands by name

Popular brands