HIKVISION DS-7204HQI-K1 User Manual Download Page 125

Page: 125 / 200

DS-72xxHUI-Kx, DS-72xxHQI-Kx Digital Video Recorder (DVR) User Manual

UM DS-72xxHUI-Kx, DS-72xxHQI-Kx 062817NA

123

Click

to clear the existing virtual line.

Up to four rules can be configured.

Figure 158, Draw Line for Line Crossing Detection

Click

Apply

to activate the settings.

The sudden scene change detection and the line crossing detection
cannot be enabled on the same channel.

9.3

Intrusion Detection

The Intrusion Detection function detects people, vehicles, or other objects that enter and loiter in a pre-defined
virtual region. Specific actions can be taken when the alarm is triggered.

Enter the VCA settings interface, Menu > Camera > VCA.

Select the camera for which to configure the VCA.

Check the

Save VCA Picture

checkbox to save the captured VCA detection pictures.

Set the VCA detection type to

Intrusion Detection

Check the

Enable

checkbox to enable this function.

Click

to configure the trigger channel, arming schedule, linkage action, and PTZ linking for the

intrusion detection alarm.

Click

Rule Settings

to set the intrusion detection rules. Set the following parameters:

Summary of Contents for DS-7204HQI-K1









































































































































































































Search results

Summary of Contents for DS-7204HQI-K1

Reviews:

Related manuals for DS-7204HQI-K1

Brands by name

Popular brands

HIKVISION DS-7204HQI-K1, User Manual

Search results

Summary of Contents for DS-7204HQI-K1

Reviews:

Related manuals for DS-7204HQI-K1

Brands by name

Popular brands