HIKVISION DS-7204HQI-K1 User Manual Download Page 168

Page: 168 / 200

DS-72xxHUI-Kx, DS-72xxHQI-Kx Digital Video Recorder (DVR) User Manual

166

UM DS-72xxHUI-Kx, DS-72xxHQI-Kx 062817NA

Figure 219, View HDD Status (2)

12.7

Checking S.M.A.R.T. Information

The S.M.A.R.T.

(Self-Monitoring, Analysis, and Reporting Technology)

is an HDD monitoring system to

detect

nd report on various reliability indicators in the hopes of anticipating failures.

Enter the

HDD Detect

interface, Menu > Maintenance > HDD Detect.

Click the

S.M.A.R.T. Settings

tab to enter the interface.

Select the HDD to analyze.

Click Test to start analyzing the selected HDD.

View the HDD’s S.M.A.R.T. information list once the analysis is complete.

If you want to use the HDD even if the S.M.A.R.T. checking has
failed, check the

Continue to use this disk when

self-evaluation is failed

checkbox.

Figure 220, S.M.A.R.T. Settings Interface

12.8

Detecting Bad Sectors

You can detect HDD bad sectors.

Enter the

HDD Detect

interface, Menu > HDD > HDD Detect.

Click the

Bad Sector Detection

tab to enter the interface.

Select an HDD and click

Detect

to start detecting.

Summary of Contents for DS-7204HQI-K1









































































































































































































Search results

Summary of Contents for DS-7204HQI-K1

Reviews:

Related manuals for DS-7204HQI-K1

Brands by name

Popular brands

HIKVISION DS-7204HQI-K1, User Manual

Search results

Summary of Contents for DS-7204HQI-K1

Reviews:

Related manuals for DS-7204HQI-K1

Brands by name

Popular brands