HIKVISION DS-7204HQI-K1 User Manual Download Page 107

Page: 107 / 200

DS-72xxHUI-Kx, DS-72xxHQI-Kx Digital Video Recorder (DVR) User Manual

UM DS-72xxHUI-Kx, DS-72xxHQI-Kx 062817NA

105

Chapter 8

Alarm Settings

8.1

Setting Motion Detection

Enter

Motion Detection

interface of Camera Management, Menu > Recording Configuration > Motion

Detect.

Choose a camera for which you want to set up motion detection,

Figure 135, Motion Detection Setup Interface

Set detection area and sensitivity.

Check the motion detection

checkbox to enable it.

Use the mouse to draw detection area(s) or click

Full Screen

to set the detection area to be the full screen.

Drag the sensitivity bar to set sensitivity.

Click

to set alarm response actions.

Summary of Contents for DS-7204HQI-K1









































































































































































































Search results

Summary of Contents for DS-7204HQI-K1

Reviews:

Related manuals for DS-7204HQI-K1

Brands by name

Popular brands

HIKVISION DS-7204HQI-K1, User Manual

Search results

Summary of Contents for DS-7204HQI-K1

Reviews:

Related manuals for DS-7204HQI-K1

Brands by name

Popular brands