Herz firestar de Luxe 18 Page 60 Operating Instructions Manual Download

Page: 60 / 90

Boiler control

the mail settings will be displayed
again.

Note:

Selection:

The box must be activated. If the status is
inactive, no E-mail will be sent to the recipient.

If the box is checked, errors will be transmitted

If the box is checked, warnings will be transmitted

If the box is checked, information will be
transmitted

ENTER MAIL SUBJECT

TEST-MAIL SENDING

Navigation:

→

Subject

Navigation:

Screen:

By pressing the button:

the entry will be confirmed.

Test-mail send

Send E-mail to recipient. (only
visible/possible if sending is active)

the last character will be deleted.

the mail server settings will be
displayed.

characters will be written in
uppercase

E-mail times setting will be
displayed.

Summary of Contents for firestar de Luxe 18



























































































Search results

Summary of Contents for firestar de Luxe 18

Reviews:

Related manuals for firestar de Luxe 18

Brands by name

Popular brands

Herz firestar de Luxe 18, Operating Instructions Manual

Search results

Summary of Contents for firestar de Luxe 18

Reviews:

Related manuals for firestar de Luxe 18

Brands by name

Popular brands