Herz firestar de Luxe 18 Operating Instructions Manual Download

Page: 55 / 90

Boiler control

9.14

System settings

Navigation:

→

111

→

Screen:

If touching symbol:

the network configuration will be displayed.

the Remote

– settings will be displayed.

information such as software version operating system number, … will be displayed.

the screensaver settings will be displayed.

messages by E-mail can be send

Display if a USB stick is plugged in (USB-symbol). Backup of USB stick create or play
(backup, software, ...) by pressing the field.

the Modbus

– settings will be displayed.

Service special

Alarm Modul (external Modul necessary

– see „user manual Alarm – Modul“)

you get to the cascade overview (see "Operating Instructions for cascade control T-
Control 2")

Summary of Contents for firestar de Luxe 18



























































































Search results

Summary of Contents for firestar de Luxe 18

Reviews:

Related manuals for firestar de Luxe 18

Brands by name

Popular brands

Herz firestar de Luxe 18, Operating Instructions Manual

Search results

Summary of Contents for firestar de Luxe 18

Reviews:

Related manuals for firestar de Luxe 18

Brands by name

Popular brands