Herz firestar de Luxe 18 Operating Instructions Manual Download

Page: 53 / 90

Boiler control

9.13.11

Additional boiler

The recommended hydraulic schemes are shown in appendix 15.1

Navigation:

→

Additional boiler

Screen:

By pressing the button:

the „additional boiler status“ menu will be displayed
(Schematic representation of the boiler and overview of various values)

the menu for the "settings" will be displayed

the menu "inputs / outputs" will be displayed

the menu "operating hours" will be displayed

Term

Description

Unit

Menu „additional boiler status“

Status 1

Boiler temperature

Indicates the boiler temperature (40-80)

°C

Flue gas temperature

Indicates the flue gas temperature

°C

Pump

Indicates the state of the back flow pump (ON/OFF)

Release / additional
boiler

Indicates the state of the release of the additional boiler: (ON/OFF)

Automatic:

Release ON / OFF

Manual:

additional boiler active / inactive

Menu "Settings"

Settings

Waiting period

Automatic:

waiting time for release of the additional boiler (if required)

Manually:

additional boiler minimum operation time till additional boiler is

available again

Setting the waiting time (1-900), until the additional boiler starts.

min

Pump trigger

Setting up pump trigger (25-65)

°C

Summary of Contents for firestar de Luxe 18



























































































Search results

Summary of Contents for firestar de Luxe 18

Reviews:

Related manuals for firestar de Luxe 18

Brands by name

Popular brands

Herz firestar de Luxe 18, Operating Instructions Manual

Search results

Summary of Contents for firestar de Luxe 18

Reviews:

Related manuals for firestar de Luxe 18

Brands by name

Popular brands