Herz firestar de Luxe 18 Page 30 Operating Instructions Manual Download

Page: 30 / 90

Boiler control

9.12

Module configuration

Boiler

Buffer

Hot water tank

Overview
Status
Settings
Inputs/Outputs
Operating hours

Overview
Status
Settings
Agg-Test
Barrier times

Overview
Status
Settings
Agg-Test
Circulation pump
Time program/Barrier times

Heating circuit

Time mode

Solar

Overview
Status
Operation modes
Settings
Agg-Test
Heating circuit curve
Time program / Barrier times

Overview
Time program
Settings

Overview
Status
Settings
Agg-Test
Yield

Hydraulic compensator

Net pump

Zone valve

Overview
Status
Agg-Test
Barrier times

Ext. requirement

Additional boiler

Overview
Status
Settings
Barrier times
Heat curve

Overview
Status
Settings
Agg-Test
Barrier times

9.13

Terms and definitions

In this chapter all parameters and terms of the different modules are explained.

Some terms can be a display value and a setting value. To recognize these, they are
marked with a *.

◼

The term is a display value if aggregate test is inactive

→

the symbol of the

aggregate test is:

◼

If the aggregate test is active (by pressing the symbol

the hand will change to

green and the aggregate test gets activated) the individual components can be tested
by pressing the control lamp. Now the term is a so-called setting value.

Summary of Contents for firestar de Luxe 18



























































































Search results

Summary of Contents for firestar de Luxe 18

Reviews:

Related manuals for firestar de Luxe 18

Brands by name

Popular brands

Herz firestar de Luxe 18, Operating Instructions Manual

Search results

Summary of Contents for firestar de Luxe 18

Reviews:

Related manuals for firestar de Luxe 18

Brands by name

Popular brands