Herz firestar de Luxe 18 Operating Instructions Manual Download Page 46

Page: 46 / 90

Boiler control

9.13.7

Hydraulic compensator

Navigation:

→

Hydraulic compensator

Screen:

By pressing the button:

the „Hydraulic compensator status“ menu will be displayed

the menu for the "Aggregate-

Test“ will be displayed

the „barrier times“ menu will be displayed

Required temperature

Indicates the required temperature of the downstream module (e.g. heating
circuit) in °C

Existing temperature

Indicates the flow temperature of the upstream module (e.g.: boiler, buffer) in °C

Term

Description

Unit

Menu "Status"

Status

Hydr. compensator
temperature

Indicates the hydraulic compensator temperature. The hydraulic
compensator has a built-in temperature sensor.

°C

Existing temperature

Indicates the flow temperature of the upstream module (e.g.: boiler,
buffer)

°C

Required temperature

Indicates the required temperature of the downstream module (e.g.
heating circuit)

°C

Pump 1

Indicates the state of pump 1 (ON/OFF)
Pump 1 is the pump in the back flow on the primary side

Switchover

Indicates the state of switchover (ON/OFF)

Pump 2

Indicates the state of pump 2 (ON/OFF)
Pump 2 is the pump in the flow on the

secondary side

Status 2

Menu "Aggregate-Test"

Agg-Test

Pump 1*

Indicates the state of pump 1:
Pump 1 is the pump in the back flow on the primary side

▪

If the indicator lamp lights up, pump 1 is switched on

Switching valve

Display of the state of the switching valve.
If the indicator lamp lights up, the switching valve is activated.

Summary of Contents for firestar de Luxe 18



























































































Search results

Summary of Contents for firestar de Luxe 18

Reviews:

Brands by name

Popular brands

Herz firestar de Luxe 18, Operating Instructions Manual

Search results

Summary of Contents for firestar de Luxe 18

Reviews:

Brands by name

Popular brands