manualshive.com logo in svg

Herz firestar de Luxe 18, Operating Instructions Manual

Share
Download
Herz firestar de Luxe 18 Operating Instructions Manual Download Page 43

Boiler control

 

9

 

 

 

43

 

9.13.5 

Time mode 

Navigation: 

 

→

 

 

→

 Time mode

 

Screen: 

 

By pressing the button: 

 

the menu for the "settings" will be displayed  

 

the menu for the 

"time program“ will be displayed 

Demand active 

Indicates the state of the active requirement of the time mode 
If the indicator lamp lights up, the requirement is activated 

Required temperature 

Indicates the required temperature in °C 

 

Display of the set times according to the time program: 
the menu for the 

"time program“ will be displayed 

 

Term 

Description 

Unit 

 

Menu "Settings" 

 

Settings 

1

 

 

Operation modes 

- manually: fix requirement (demand temperature) during the set time 
- via ModBus: requirement via ModBus during the set time (address: 45000-
45022) 
- weather compensated: requirement via heating curve during the set time 

- 

Time requirement 

If the boiler works only as a heat supplier (no heating circuit installed), the set 
up boiler set temperature (20-100) gets supplied during the set heating times. 

°C 

Min. loading 

Indicates/activates the min. loading (20-58) (ON/OFF) 

▪

 

Outside of the hot water tank loading time, the hot water tank temperature 

is loaded to the set min. loading. 

If hot water tank temperature is lower than the min. loading / temperature 
value, the hot water tank loading will start 

°C 

 

Menu "Time program"

 

 

Time program 

1

 

 

Time 1  

1 - 3 times can be set. The second and third time can be added by the +. 
Example: 

▪

 

time 1: 

08:00 

– 10:00 

▪

 

time 2: 

15:00 

– 21:00 

▪

 

time 3: 

00:00 

– 00:00 

- 

08:00 

– 11:00 

Setting up individual hot water tank loading times of every weekday 

- 

 

By pressing the symbol Monday preset gets assigned to remaining 
weekdays 

- 

Summary of Contents for firestar de Luxe 18



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands