manualshive.com logo in svg

Herz firestar de Luxe 18, Operating Instructions Manual

Share
Download
Herz firestar de Luxe 18 Operating Instructions Manual Download Page 16

8

 

Temperature manager

 

 

16 

If the required buffer-top-temperature (required temperature) is higher than the sum of buffer-bottom-MUST-
temperature and the set difference, then the required boiler temperature is the result of the required buffer-
top-temperature  (required  temperature)  +  the  adjusted  temp.  increase  (see  Fig.8.2).  Caution:  Consider  the 
set minimum requirement.

 

 

 

Fig.8.2: Example temperature manager with buffer and without difference 

 

If  the  required  buffer-top-temperature  (required  temperature)  is  lower  than  the  buffer-bottom-MUST-
temperature  than  the  required  boiler  temperature  is  the  result  of  the  required  buffer-bottom-temperature  + 
the  adjusted  temp.  increase  +  the  adjusted  difference  (see  Fig.  8.3).  Caution:  Consider  the  set  minimum 
requirement. 
 

 

Fig. 8.3: Example temperature manager with buffer and difference 

 

Summary of Contents for firestar de Luxe 18



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands